Hogs and Wood Grinders For Sale
Category
Hogs and Wood Grinders
.gif)
177 Results Found
WSM - 2852BH, ...Heavy Duty Hammermill/Shredder. -- 200 HP - 1,165 RPM Motor -- Infeed opening size: 52" L x 28" W -- Infeed with: Feed roll, 1-1/2" teeth with 6" spacing. -- (2) Types of Hammers: One a rounded style with hard-faced tips.Machine is part of a Pallet Recycling Plant and includes: -- Pallet Feeder -- Dual Chain Conveyor. -- Vibratory Feeder. -- Inclined Oscillating Table.
MLS Number 12321010 WEST SALEM WSM5472 Horizontal Grinder -60” Millpower Shaker conveyor/finger screen – deck removed, used to meter flow of material fed by operator and reduce bed depth to make cross belt and head pulley magnets most efficient. -60” Eriez cross belt electro magnet. -Eriez 10K42 kW Silicon Rectifier incorporating: To convert 480 volt, 60 Hz, 3 phase AC to230 volt DC 10,000 watts output Normal convection cooled, full wave bridge circuit Fused AC switch Nema 3r Enclosure -Eries beefy magnet stand to support magnet and chain fall. -60” x 28’6” Slider Bed (Heavy Duty Feeder Type Conveyor) with 8’ section of stainless steel non-magnetic for Eriez cross belt magnet to perform at peak -20”x60” Dodge magnetic head pulley – installed to double up on magnets on conveyor, prior to material entering WSM grinder drag chain feed. Downstream from this is the WSM 5472bh Titan horizontal grinder. Schematics and wiring diagram can be supplied as well. WSM also supplied the chip discharge conveyor and magnetic head pulley and electrical panel with touch screen (by Emerson). Price includes dismantling and loading on buyer's truck. Manuals available for components.
WILLIAMS - Hammer Mill: Half-round Type ConfigurationFeatures: -- 220 HP Main Drive Motor with Belt Drive; complete with Guard. -- 26"; x 12"; Input Opening. -- Powered Input Pull Rolls -- 4"; Main Shaft with Swing Hammers, approx. 3/8"; thickness -- Ratchet Lift Access Lid. -- Mounted on Steel Support Structure with Access Platform and Ladder -- Pneumatic Bottom Discharge with built-in Viewing Window in Ducting below the Hammermill (no fan included) -- Electrical Cabinet with Motor Starters -- NOTES: This machine was last utilized to break up virgin dried pulp for further processing. Already been removed from service – ready to load.
Call for Price
Call for Price
Williams 125 HP Hammermill 230/460 3-phase
Call for Price
100 HP 230/460 volt 20” x 19” inlet 9” x 28” outlet no hopper
Hammer Mill. This machine is a Williams hammer mill. Item #C549
Williams Hog S/N 14482 150HP Electric Motor
Williams Hammer Hog 30 with 125HP Motor S/N 20053
MLS Number 10791295 Williams Horizontal Wood Hog 200 HP 24" wide 16 Ft vibrating conveyor With soft start
.jpg?width=300&height=200&mode=pad)
Williams Horizontal 50" Grinder with Webster Vibrating Conveyor s/n 20492, 200hp motor
Call for Price
32" Vertical grinder with 25 HP motor Dentom 624 9500 BTU Furnace automated measured feed controlled by furnace temperature Holding tank for feed from the grinder which is automatically fed to the furnace...that feed is temperature controlled.
Woodsman 790 Grinder Power it how ever you want Was Running off a Diesel Power Unit.
1994 Zeno ZTLL 1400 x 1600 Slow Speed Low Noise Grinder 55HP 480V & Hood
1993 Zeno ZTLL 1600 x 2300 slow Speed Grinder 125HP 480 3 Phase Motor S/N 93A-366
MODEL ZTLP 1800 X 1600 Zeno Low Noise Single Shaft Shredder/Chipper Specifications: --Model ZTLP 1800 X 1600 -- Feed opening 70’’ (1800mm) wide x approximately 62’’ (1600mm) long. --24’’ Diameter x 70’’ long single rotor with bolt-on blades. --Hydraulic pusher ram feed. --Shredder driven by a 105 kW (140 hp) --3/60/460 volt --1780 rpm motor --No Control Panel --New in 2005