Hogs and Wood Grinders For Sale

125 HP 460 Volt 28” x 44” inlet 7” x 40” outlet hopper included as pictured

Jeffrey Hammer Mill 30WB S/N 14168

JMC McIntyre MODEL 610 24" Alligator Shear The McIntyre 610 is a 24";(610 mm) blade general purpose scrap yard shear which cuts up to 2.5"; (63 mm) plus all usual medium sized structural sections.This industry workhorse has been reconditioned to a high standard, guaranteeing many more years of reliable service.Technical Specifications --Blade length - 24" (610 mm) --Max blade opening - tip to tip 14" (355 mm) --Shearing height - 32" (812 mm) -- 600 VoltCutting control - Lever Automatic / Single Stroke

JWC ENVIRONMENTAL Muffin Monster 3-Shred-H-800 Shredder/GrinderSpecifications: -- Model #: 3-Shred-H-800 - Stainless Steel -- Used only two times -- Stainless steel construction -- Alloy steel drive shafts and scrapers -- Cartridge-style tungsten carbide mechanical seals -- Mill opening:Length: 7 inches Width: 9 inches -- 5 HP motor -- Electrical:230 V 60 Hz Phase 3

Kimwood Grinder with 200HP Electric Motor

LAMB 23x27 inch opening grinder with 150 HP motor, 1 3/8” screen and starter control. 460 volt 3-phase

Montgomery Blo Hog S/N 781 ER18" HDGM Drop Feed w/75HP Motor

Montgomery Blo-Hog, drop feed Steel Flywheel for surge loads Top infeed opening: 18 ¼ X 13 1/4” Bottom discharge Will be repainted Model: ER 18S315FHDL Serial # 1032 75 hp motor. 230/460V, frame: 405T, Support stand Extra parts Contact us for a delivered price

Jacobson Swing Hammer Mill, Top Infeed, Bottom Discharge, 75HP Electric Motor.

Montgomery Blo-Hog model: 1540-18 HD-BHL s/n: 1581

2022 Morbark 3000XT Horizontal Grinder -180 hours -575 hp CAT engine -Remote -Still under warranty NEW NEW NEW

2018 Morbark 3400XT Wood Hog Horizontal Grinder CAT C18, 765 Hp engine Approx 2100 hours New belly belt/skirting; Rebuilt mill Engine has new cylinder sleeves with rod & main bearings, purge pump & hydraulic fan motor (replaced by manufacturer due to a defect) Remote Magnet 1” & 5” screens Great machine and ready to go to work

MULTITEK - TRC 460, ...Rim Crusher: ...Less than (300) Hours!Features & Specifications:• Tough MULTITEK® products; simple and strong. Truck Rim Crusher makes wheel salvage easier. • Powered by: Fuel-efficient 25 HP liquid-cooled diesel engine with operator instrument panel control.• The powerful MULTITEK built 6" (15.2 cm) diameter hydraulic cylinder features a Heavy-Duty aluminum piston for continuous duty cycle application.• Power-assisted hydraulic wheel lift arm means less work to load heavy truck wheels.• Powerful 70,000 Lbs (31,752 kG) of crushing force.• Simple: Minimal training and maintenance required.• Standard 2"; ball hitch.• Dimensions: 80" (203 cm) W x 171" (434 cm) L; weight: 3,400 Lbs (1,542 kG).• Engine: Liquid-cooled Diesel with electric start.• Cycle Time: (35) Seconds.

OVERBUILT - 10 Portable, ...Car CrusherIncludes Remote, FULLY LOADED. Specifications: -- (2) 10" Cylinders. -- Height: 10 ft. (raised); 24" ( lowered). -- Width: 7-1/2'. -- Length: 20-1/4". -- Lid movement: 8 ft. (Travel) -- Hydraulic cylinder: 10" x 4" Rod x 96" travel. -- Pressure: 2,400 PSI. -- Crushing force: 159 Tons

2003 Peterson HC5400 Grinder -7700 hours -New set of bananas, grates, and teeth -Has a wireless remote -Rotor recently balanced and serviced -New tires ands wheel bearings on axle -Comes with 25K worth of parts MACHINE RUNS AND WORKS BUT NEEDS A FEW MINOR REPAIRS -Has a hole in the metal plate that covers the rotor -Has a small leak in the fuel tank we currently use an auxiliary tank -Intermittent issue of conveyor not feeding. Believe it is a broken wire

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

Progress waste grinder, swinging hammer style, 125 hp electric drive, 1185 rpm's, unit needs to have hammers installed, good overall condition

Progress Industries 24" x 48" DFBD Swing Hammer with 200HP Motor.