Edgebanders For Sale

Brandt Optimat KDF 230C Edgebander

Brandt KDF 440 Highflex 1440 Edgebander

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

BRANDT OPTIMAT KDN 650 C Edgebander, with Corner Rounding, Pre-Melt, & 8,654 Hrs. (As of 6/2/22) Specifications: -- Edgebanding thickness 0.4 - 8 mm (0.02" - 0.31"). -- Panel thickness 8 - 55 mm (0.31" - 2.17"), Min. panel width 65 mm (2.56"), Min. panel length 160 mm (6.30"). -- Feed speeds 11/14 FPM (36/46 FPM). -- Working height 950 mm (37.40").Equipped with: -- 32-1/2" Dia. Coil table. -- Automatic magazine. -- 3 mm (0.12") Guillotine. -- "Quick-Melt" Hot melt glue unit, with Heat-up time: Approx. 12 min., Pre-melt hopper feed, Quick-change hopper & tank for color changes, Reversible glue applicator roller rotation, & Retractable glue roller. -- Pressure section, with (1) Large driven & (3) Small pneumatically-controlled idler rolls. -- "POWER CONTROL PC 20+" Control, with 600 MHz, 256 MB RAM, USB Port, 1 GB Flash card, Internal modem for remote diagnostic access link, & 12" TFT Flat screen monitor. -- Line control (no limit switches) for workstation functions. -- Feed chain, with 2.2 kW (3 HP) Feed motor & Automatic chain track lubrication. -- Digital height indicator. -- Sound enclosure.Workstations: -- Front & rear end trimming unit, with (2) 0.35 kW (1/2 HP) - 12,000 RPM High frequency motors, 0° - 15° Chamfer, & Programmable pneumatic control for straight or chamfer trimming. -- Top & bottom flush trimming unit, with (2) 0.55 kW (3/4 HP) - 11,300 RPM High frequency motors, 0° - 25° Swivel, & Combination straight/radius cutters. -- Corner rounding unit, with (2) 0.35 kW (1/2 HP) - 10,940 RPM High frequency motors & 3 mm (0.12") Radius insert cutters. -- Top & Bottom Profile scraping unit, with Vertical & Horizontal tracing. -- Top & bottom buffing unit, with (2) 1/4 HP - 1,400 RPM Motors and Vertical & Horizontal tilt.

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

BRANDT - F-13, ...Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL, and veneer edgings; up to 3 mm max. thickness. -- Manually operated; 1/2" - 2-1/4" panel thickness; 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each). -- Built-in air jet blowoff device; 31" x 48" table size; dual foot pedal control.NOTE: Intermittent fault in the Control Panel, which will require replacement.

0.4 -3 mm (1/8") Edge cap., panel thickness from 8 -40 mm (5/16" -1-9/16"), min. panel length 120 mm (4- 3/4") and 70 mm (2-3/4") min. width. Feed Speed: Feed chain track speed 8 MPM (26 FPM) w/gear motor feed drive not under power Pre-Mill Station: 2-Motor Pre-mill (1 HP-12,000 RPM @ 200 Hz). Gluing Station:"A3" Gluing Unit for granulate adhesive application system with Quick Change application unit underneath glue reservoir, Automatic reduction of glue temperature upon interruption of work. Automatic magazine for coil (table 800 mm dia. to accommodate large coils of 3 mm material) stock Heavy Duty guillotine, strips stacking with automatic strip separation on feeding. Pressure zone with driven main roller & (2) idle post pressure rollers; Digital readout for manual adjusting pressure zone to edge thickness. Work stations: • End trim of front & rear edge (0.24 HP - 12,000 RPM@ 200 Hz motor ea. with 100 mm dia. saw blade). • Top & bottom Flush/Chamfer/Radius trimming(0.36 HP - 12,000 RPM @ 200 Hz motor ea.), sensing horizontally & vertically, DFC combination cutters for flush, chamfer, & radius trimming; (1) set of tools for 3 mm radius, digital readouts for fast adjustment. • Radius Glue Joint Scraping unit Top & bottom for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam. • Glue Joint Scraping unit Top & bottom for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam, equipped with (2) reversible cutter knives. • Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad. • Complete With: Top pressure with (2) single rows of staggered rubber rollers Transport chain with 80 mm wide with replaceable rubber pads Work piece support track extends up to 300 mm (11.8"). Individual dust extraction ports and Sound & safety enclosure.

BRANDT - AMBITION 1200 (aka KDN-200), ...Edgebander (Compact) -- Specifications: 0.4 - 3 mm (1/8") Edge thickness cap.; 8 - 50 mm (0.3" - 2") panel thickness; 60 mm (2.3") min. panel width; 40 mm (5-1/2") min. length. -- Hot Melt granulate glue system with: "Quick Melt" start-up (10 - 12 Min heat up) with: Reversible rotation glue applicator roller; automatic reduction glue temperature adjustment (when idle, drops to 150°; 2-1/2 Min to reactivate). -- Includes: Automatic feed magazine; coil stock feeds automatically with guillotine cutoff; all strip stock fed automatically through strip feed magazine. -- 3-Roller pressure Section: 1st Driven; next (2) are idle and electronically controlled; feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with: Tilting of 0° - 15° cap.; 0.24 HP - 12,000 RPM motors. -- Top & Bottom multifunctional trimming Units: 0.36 HP - 12,000 RPM Motors; bevel 0° to 15°. -- Top & bottom buffing unit: 0.15 HP - 2,750 RPM Motors.Equipped with: -- Eye level Operator control panel. -- Automatic height adjustment with top pressure beam for all workstations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers. -- Feed speed: 30 FPM.Includes: 200 Hz Electronic frequency inverter; used tooling; sound enclosure w/window; Operators manual. -- Actual Model: BRANDT AMBITION 1200 (aka KDN 200).

BRANDT AMBITION 1200 (EDGEBANDER WPRE-MILL & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity, 0.4 - 3 mm Edge cap., min. panel thickness 8 mm (0.3"), max. panel thickness 40 mm (1.57"), min. panel width 70 mm (2.75"). Min panel length: 140 mm (5.5")Line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all workstations. Auto in-feed stop to insure proper spacing between panels. Equipped with:Pre-Milling Station:(2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Gluing Section:Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, Pressure Section with (1) large drive plus (2) idle rollers "pneumatically controlled." Hot Melt granulate quick heat-up glue system. Workstations: End Trimming: 2 x 0.18 kW (1/4 HP), 12,000 RPM motors, THK guided, chamfers 0° - 15°. -- Flush/Bevel/Radius Trimming:2 x 0.55 kW (0.75 HP),12,000 RPM motors with insert knives for 3 mm PVC radius. cutter-heads, bevels 0° - 15°. -- Corner Rounding Station:1-Motor (4-corners) contour trim for profile corner rounding, 1 x 0.35 kW (0.5 HP), 12,000 RPM motor, with insert knivesFor 3 mm PVC radius w/digital read-out set-up and pneumatic change-over from thin to thick PVC edge tape. -- "Quick-Change" Profile Scraping Unit:Top & bottom for 2 - 3 mm radius, pneumatically controlled blow-off nozzles. -- Flat Scraping Unit:Top & bottom flat scraping units with copy wheels to remove residual glue squeeze-out.Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Complete With: &#9679 Trim stations have HF motors w/electronic brakes &#9679 Fixed feed chain track speed of 8 MPM (26 FPM) &#9679 2 HP feed drive &#9679 208/230/440/480v, 3ph Transformer &#9679Sound/Safety Enclosure &#9679 Adjustable Out-Rigger Support &#9679 Used tooling. -- Actual Model is BRANDT AMBITION 1200.

BRANDT AMBITION KDF 1230 FC (KDF 230C) (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Edge material thickness 0.4 - 6 mm (0.016 - 0.23"); panel thickness 0.8 - 40 mm (0.03 - 1.57"); min. panel length 160 mm (6.29"); min. panel width 70 mm (2.75").Equipped with: -- Pre-Milling Station, (2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. -- Infrared Radiant Quartz Heating Unit: Between glue roller and pressure section. -- Automatic Edge Magazine: For strip & coil stock, strips 0.4 mm - 3 mm (0.016 - 0.011"), coils up to 3 mm PVC; "HD" guillotine. -- Gluing Station: "A3" Gluing Unit for granulate adhesive application system with Quick Change application unit underneath glue reservoir. -- "Quick Change" Glue Tank: For maintenance & glue color change. -- Pressure Section: 1st. roller driven plus (2) idle rollers, Digital readout for manual adjusting pressure zone to edge thickness. Timed pneumatic pressure controlled; -- Feed Speed: Feed chain track speed 11 MPM. (36 FPM) w/gear motor feed drive.Workstations: -- End Trimming: (2) Motor @ 0.18 kW (0.24 HP) 12,000 RPM, automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/bottom (2) motors, 0.27 kW (0.36 HP) 12,000 RPM, tilt positioning 0° - 25°, with combination flush/radius/chamfer cutter-heads; horizontal and vertical tracing wheels. -- Corner Rounding Unit: (1) Motor 0.35 kW (0.5 HP) 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Radius Scraping, Multi-Profile: Top/bottom with (2) profiles. 1 mm & 2 mm or 3 mm instead of 2 mm, PVC scrape collection box. -- Flat Glue Joint Scrapers: Top & Bottom Glue Joint scrapers for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam, equipped with (2) reversible cutter knives. -- Buffing Units: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors Top & Bottom Buffing Units.Operator & Machine Control: -- "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Actual Model is BRANDT AMBITION KDF 1230 FC (KDF 230C)

BRANDT "KDF-980 2C" EDGEBANDER WORTH PRE-MILLING & CORNER ROUNDING 0.4 - 20 mm (3/4") Edge thickness capability; Min. workpiece width 65 mm (2-1/2") and min. panel length 160 mm (6-1/3"), panel thickness 8 - 55 mm (5/16" - 2-3/16") .Working height 900 mm (35"); 80 mm wide Heavy Duty feed chain w/rubber pads, automatic chain track lubrication, 3 HP (2.2 kW) feed drive for variable feed speed 11 - 20 MPM (36 - 65 FPM) (max. using solid wood 52 FPM); motorized upper pressure beam.7.4" Matrix color LCD Screen "PC-16" Integrated Microprocessor Line control for programming the various working functions; features internal modem for remote diagnostic link.Pre-Milling Station, (2) 3 HP (2.2 KW) - 12,000 RPM Vertical milling/jointing heads, electro-pneumatic jump control, heads counter-rotate, SIKO digital units for vertical & horizontal adjustments.Quickmelt gluing system with large granulate hopper with automatic glue feed system (approx. 12 Min heatup time); pre-melting unit between hopper and reversible & retractable glue roller; infrared radiant glue heat zone between glue roller and pressure section for optimum gluing strength.Automatic magazine for strip and coil feeding with automatic coil feeding system; 2-coil table for one roll thick PVC and one for thin edgings; wide magazine with automatic feeding of wood strips; program controlled.Motorized pressure section with (1) large driven pressure roll and (4) secondary idle rollers with pneumatically controlled side pressure; solid wood infeed device.Workstations Edgebanding:End Trimming (1 HP / 0.75 kW) - 12,000 RPM motor, program controlled pneumatic indexing of straight or chamfer trimming, chamfers up to 15°.Top & bottom rough (flush) trimming (2 HP / 1.5 kW) - 12,000 RPM motor ea. w/vertical tracing.Top & bottom fine trim (0.75 HP /0.55 Kw) - 12,000 RPM motor ea., bevel 0° - 25° tilt angle, w/vertical & horizontal tracing, servo driven in/out adjustment controlled from control panel.Corner rounding unit with (2) motors ( 0.50 HP / 0.4 Kw) - 12,000 RPM motors ea, 16 MPM (52 FPM) operating feed speed, pneumatic (in/out position) control from control panel (all trim station motors are 200 Cy HF and equipped w/electronic brakes). Top & bottom scraper for finishing PVC edging.Hot air blower (post heating) for reactivating scraped, thick PVC edgebanding.Top & bottom "oscillating & jump" buffing unit (0.3 HP - 2,800 RPM motors), tilt vertically & horizontally.Complete with: All working units & fence adjustment throughout machine with SIKO digital readouts, operator controls on overhead swivel arm.Includes: Sound enclosures with 1" thick padding over all milling stations in edgebander section, and digital counter at infeed to measure footage of product edgebanded.A 20 year old machine with 3573 hours on it !only ran for 15 hours per month all parts and tech support available from Homag Brandt

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on hold-down beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT - KDN 330, ...Compact EdgebanderSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12"); max. edge banding height: 45 mm (1.77"). -- Panel thickness: 8 - 50 mm (0.31" - 1.97"); min. panel width: 60 mm (2.36"); min. panel length: 140 mm (5.51"). -- Feed chain height: 35"; feed speed: 11 MPM (36 FPM); outboard support adjustment: 13".Equipped with: -- 800 mm (31-1/2") Dia. Coil table. -- Hot-melt granulate glue system with (10 - 12) Min heat-up time; reversible rotation glue applicator roller; automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min. to reactivate). -- 3 mm (0.12") PVC Pneumatic guillotine with double-acting pneumatic cylinder; automatic feed magazine; roll & fixed length. -- Pressure section with: (1) Large electronically controlled & feed speed synchronized driven and (1) small idler roll. -- 0.55 kW (3/4 HP) Feed belt motor; touchpad control with LCD Display; sound enclosure.Workstations: -- Front & Rear End Trim Unit with: (2) 0.18 kW (1/4 HP) - 12,000 RPM - 200 Hz Motors with electric brake; 0° - 15° Chamfer. -- Top & Bottom Flush/Bevel Trim Unit with: (2) 0.27 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors with electric brake; combination insert knifes for flush & bevel trimming; vertical & horizontal tracing; 0° - 15° chamfer. -- Top & Bottom Buffing Unit with: (2) 0.09 kW (0.12 HP) - 2,710 RPM Motors. -- Manual height adjustment of top pressure beam for all workstations with Digital height gauge.Complete with: -- Documentation.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Min or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. -- Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT - KDN 520, ...Edgebander0.4 - 8 mm (5/16") Edge cap.; panel thickness 15/32" - 2-5/32"; min. panel length 160 mm (6-3/8"); 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with: Top pressure beam for all workstations; equipped with digital height indicator.Specifications: -- PC-16 Program Control; 7-1/2" VGA screen 8 MB IDE flash disk; 8 MB RAM; internal modem for remote diagnostic link; signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system (approx. 12 Min); glue tank for maintenance & glue color change. - Glue temperature indicator for both the glue pot and glue roller with: LED Thermostat and automatic temperature reduction if the machine is idle for (15) Min or more. -- Glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock; 3 mm PVC guillotine; (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double-end trim (0.33 HP - 12,000 RPM motor); chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim; bevels 0° - 15° (0.5 HP - 12,000 RPM motors). -- Top & bottom scraping for 3 mm radius; pneumatically controlled indexing system. -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations: HF Motors w/electronic brakes; feed chain track speed 36 FPM; 2 HP feed drive. --Complete with: Operator Control Panel with: PLC (Programmable Logic Control) keypad & LED readouts; used tooling. -- Machine in use and available time to be confirmed.

BRANDT - KDN-530C, ...Single-Sided Edgebander with Corner RoundingNOTE: in 2010 Seller purchased NEW in crate, and all workstations are adjusted by Servo motors.Specifications: -- Edge thickness cap.: 0.4 - 6 mm (0.02" - 0.24"). -- Panel thickness cap.: 5/16" - 1-5/8"; min. panel length: 160 mm (6.30"); min. panel width: 65 mm (2.56"). -- Feed speed: 36 FPM.Equipped with: -- Line control (No limit switches) for workstation function. -- Automatic height adjustment with: Top pressure beam for all workstations & digital height indicator for 8 mm - 40 mm (0.31" - 1.57") panel heights. -- "POWER CONTROL PC-20+" Control with: PLC (Programmable Logic Control); VGA Screen; Touchpad; internal modem for remote diagnostic link; signal infeed light to insure proper spacing between panels. -- Quick heat-up glue system; heat-up time approx. 12 Min with: Glue tank for maintenance & glue color change; glue temperature indicator for both glue pot & glue roller with LED thermostat; automatic temperature setback if machine is idle for (15) Min; glue applicator roller is reversible & retractable from fence line. -- Automatic magazine for strip & coil; 800 mm dia. (31-1/2") coil table accommodates large coils of 3 mm (0.12") PVC stock; 3 mm (0.12") PVC Guillotine. -- (1) Drive plus (1) split secondary roller, pneumatically controlled pressure sections. -- 3 HP Feed motor.Workstations: -- End trim unit, with 1/4 HP - 12,000 RPM High-frequency motors with Electronic brakes, Chamfers 0° - 15°. -- Top & bottom flush/radius trim unit, with 1/2 HP - 12,000 RPM High-frequency motors with Electronic brakes, Bevels 0° - 15°, with Insert knives for 3 mm (0.12") PVC radius & "Quickset" with Digital counters. -- Single-motor corner rounding unit, For "On-the-fly" corner rounding, with 1/2 HP - 12,000 RPM Motor. -- Top & bottom scraping unit, For 3 mm (0.12") Radius, with Pneumatically-controlled indexing system & Dust collection. -- Top & bottom buffing unit, with 1/4 HP - 2,800 RPM Motors.Complete with: -- Manual.NOTE: Seller estimates he ran (70,000) parts on machine.

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

BRANDT KDN 650 C Edgebander; 6-Station Edgebander with 0.4 - 8 mm (5/16") Edge capacity. Specifications: -- Panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; -- Line control (NO limit switches) for workstation function. -- Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator. -- PC-16 Program Control with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; -- Signal infeed light to insure proper spacing between panels. Equipped with: -- Quick heat-up glue system (10 to 12 minutes). -- Automatic magazine for strip & coil stock (large coil table 800 mm diam. to accommodate large coils of 3 mm PVC), 3 mm PVC guillotine; -- (1) Drive plus (3) idle roll "pneumatically controlled" pressure sections. Workstations: -- End trim (1/3 HP - 12,000 RPM motors) chamfers 0° - 15°; -- Top & bottom flush trim, bevels 0° - 15°, (2) 1/2 HP - 12,000 RPM motors) with insert knives. -- 2-Motor (4-corners) contour trim for profile corner rounding (2) 1/2 HP - 12,000 RPM motors), with insert knives for 3 mm PVC radius. -- Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. -- Last Station: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Feed chain track speed 42 FPM, 2 HP feed drive. Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling.

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.