This machine has been cleaned, repaired and checked over, ready for a new home! (2) 3HP motors 460V 3Ph 6 pneumatic stops for use in horizontal or vertical drilling 72" precision machined back fence 6 fence stops, 4 table stops (2) 23-spindle drilling heads, one horizontal, one vertical 3-position turret dept stop on vertical head 5 pneumatic holddowns Magnetic motor controls 32mm spindle centers 10mm collet diameter 1725 RPM spindle speed 90 PSI air requirement 3" max. drill stroke

(2) 3 HP Spindle Driver Motors Wired 3-Phase 240 30" X 48" Work Table Surface

Manufacturer’s Specification Model EG800A ELECTRO GLUE RADIO FREQUENCY EDGE GLUER Feeds Left to Right Curing Area: 36” deep by 96” long. Clamping Capacity: 41” deep by 96” long by 2” thick. Side Pressure::Applied by (16) 5” bore by 12” stroke air cylinders on 6” centers. Cylinders are NFPA Standard “Parker” Cylinders Top Pressure: Applied by (4) 3 1/4” bore by 18” stroke air cylinders. Cylinders are NFPA Standard “Parker” Cylinders Generator: A built in 30 kW. Radio Frequency generator cures approximately 3,000 square inches of glue line per minute. The generator is completely enclosed in aluminum housing. The generator also features a vacuum variable for improved efficiency and performance. Operators Control Panel: Includes adjustable cycle timer, necessary meters, indicator lights, control pushbuttons and a two hand, no-tie-down control system for closing the press. System Controls: The system is controlled by an Allen Bradley PLC. The system is equipped with a rotary disconnect that is mounted on the electrical panel access door. All PLC outputs and branch circuits are fuse protected. Safety: An electronic eye prevents closing of the press in the event any objects are inserted from the front. All access doors are interlocked to prevent use of the generator in the event any are open. A safety switch is used to prevent the use of the generator when the press is in the open position. Voltage: Installation: Quoted price includes the services of a Rosenquist technician to assist with the installation of the equipment and training of production and maintenance personnel. Included are all travel and living expenses. Delivery: Currently 12-14 Weeks INCLUDED OPTIONS Smart Cure: This feature utilizes the capabilities of the plc to monitor the cure rate of the adhesive and will automatically end the cure cycle once the adhesive is set. This will eliminate the need for the operator to calculate the amount of glue line and manually setting the RF cycle timer. The system is also equipped with the standard cycle timer. ????????? Automatic Power Control: Eliminates the need to adjust the power control manually. Eliminates human error associated with incorrect power settings. Slightly faster cure cycles will be realized. Recipe Control: This feature allows a specific recipe for a particular species or product to be stored in the PLC. The recipe control system will automatically set the “Edge Pressure”, “Smart Cure Settings”, Dwell Time” & “Power Level” for each recipe. A recipe is recalled by depressing one of the illuminated pushbutton located at the operators control console. Powered In-feed Table: provides a convenient workspace for the operator to compose a set of panels while the press is closed. Pusher is powered by an electric motor that is controlled by an inverter drive. Includes all necessary push buttons and controls. Out-Feed Table: A metal table mounted on the same angle as the press with an area of 96” long x 42” wide. ????

Rotex 6' x 16' Chip Shaving Screen

Rotex HICAP 2100 Chip Screen

Specs: Model GH-2 3 Hp, 230/460 volt three phase drive motor Belt drive to spindle arbor design (2) Spindle drill head with adjustable centers Min drill centers 1" Max drill centers 9" Spindle speed 3000 rpm Machine weight 650 lbs Vertical table adjustment 4" 24" wide x 12" long machine work table Pneumatic stock clamping Pneumatic cylinder stroke of drill head Foot pedal pneumatic controls Square D push button motor controls

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

There are two of these systems available. They were recently removed from the current operation and available immediately.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

The seller has confirmed that this Yates American resaw was in working/running condition when it was pulled from production. It is ready to load! - Vertical resaw - All parts and blades included - Approximately 35 years old - 50-60HP - 440 amp

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Planer Head Set Up Stand

Yuasa saw analyzer, great working condition comes with saw centers, magnifying camera and monitor.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

Recently removed from service Available immediately

15" color "Touch Screen" with Industrial Computer for setup and running CNC control of machine setup in less than one minute All components sized to handle 6x30 dowels Three v-groove heads with minimum 4" center to center Three banks of nine spindles for drawer front drilling One additional nine spindle bank to handle four sided drawers Two nine spindle horizontal banks for dowel drilling Runs up to 22 parts/minute in production Application Ability to v-groove drawer parts from 25" to 96" in length Ability to run parts as short as 10" without v-groove Ability to handle parts from 2-1/2" to 13-3/4" in width Ability to handle material thicknesses of 7/16" & 1/2" Makes box drawers with dowel construction Makes box drawers with 3 miters & 1 butt joint CNC Setup of machine Hopper loading of parts Parts feed through to the rear of the machine Like New Machine has run less than 100 parts. NEW PRICE: $235,000

15" color "Touch Screen" with Industrial Computer for setup and running CNC control of machine setup in less than one minute All components sized to handle 6x30 dowels Three v-groove heads with minimum 4" center to center Three banks of nine spindles for drawer front drilling One additional nine spindle bank to handle four sided drawers Two nine spindle horizontal banks for dowel drilling Runs up to 22 parts/minute in production Application Ability to v-groove drawer parts from 25" to 96" in length Ability to run parts as short as 10" without v-groove Ability to handle parts from 2-1/2" to 13-3/4" in width Ability to handle material thicknesses of 7/16" & 1/2" Makes box drawers with dowel construction Makes box drawers with 3 miters & 1 butt joint CNC Setup of machine Hopper loading of parts Parts feed through to the rear of the machine Like New Machine has run less than 100 parts. NEW PRICE: $235,000