1- 5mm Boring and Inserting Unit with Vibratory Hopper 1-8mm Boring and Inserting Unit with Vibratory Hopper Power: 208v-220v, 3 Phase, 30 Amps 96? Maximum Work Zone 4 zone stops 3-Axis Control For Positioning Weight 6,000lbs Solid One-Piece Welded Tubular Steel Frame Footprint (L x W x H): 135? x 45? x 82? Shipping Dimensions (L x W x H): 42.3? x 49? x 43? Shipping Weight: 7500 lbs

Hot Air Edgebander for Preglued banding 0.4 - 1.5 mm thickness Automatic cutoff for up to 1/32" Coil feed with manual feed for strips Panel thickness 10-50mm Front and rear end trim Top/bottom trim

LAMB 23x27 inch opening grinder with 150 HP motor, 1 3/8” screen and starter control. 460 volt 3-phase

Model # 01-1172-05-01 60” x 142” table size (1) available no hydraulic units or hand control

Leadermac Moulder 12" Capacity 10-Heads: #1 10 HP, #2 25 HP, #3 25 HP, #4 25 HP, #5 25 HP, #6 30 HP, #7 30 HP, #8 30 HP, #9 30 HP, #10 15 HP 140 FPM with 15 HP feed motor ATS Heads on Top and Sides Second machine available for parts only: Spare castings, gearboxes, pendulums, control panel, spindles

Leadermac LMC-623H Moulder with Infeed Deck This system has not run in year and will need repair.

Leadermac LMC 418-S 4 head moulder 20-80 FPM feed spiral head on bottom 460 volt 3 phase

Specs: Model GH-2 3 Hp, 230/460 volt three phase drive motor Belt drive to spindle arbor design (2) Spindle drill head with adjustable centers Min drill centers 1" Max drill centers 9" Spindle speed 3000 rpm Machine weight 650 lbs Vertical table adjustment 4" 24" wide x 12" long machine work table Pneumatic stock clamping Pneumatic cylinder stroke of drill head Foot pedal pneumatic controls Square D push button motor controls

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

There are two of these systems available. They were recently removed from the current operation and available immediately.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Planer Head Set Up Stand

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

Accu-Systems MMTJ Door Machine

75 KVA 480 volt to 240 volt

AEM 36" Sander